Teledyne Model T200 Chemiluminescence NO/NO2/NOx Analyzer
The Model T200 NO/NO2/NOx analyzer uses the proven chemiluminescence detection principle, coupled with state-of-the-art electronics to allow accurate and dependable low level measurements for use as an ambient analyzer or dilution CEMS monitor. A unique AutoZero feature provides superb stability by continuously correcting for zero drift, while advanced Adaptive Filtering allows the analyzer to optimize performance under changing conditions. The Model T200 includes a permeation inlet dryer for ozone generation to provide excellent reliability with no periodic replacement required. A catalytic exhaust ozone scrubber is standard for maximum safety and pump life. All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/0, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports either locally or by remote connection using the Ranges: 0-50 ppb to 0-20 ppm,
user selectableincluded APIcom™ software.
Features:
Ranges: 0-50 ppb to 0-20 ppm user selectable
Independent ranges and auto ranging
Large vivid and durable color graphics display with touch screen interface
Ethernet RS-232 and (optional) USB com ports
Front panel USB connections for peripheral devices and firmware upgrades
8 analog inputs (optional)
Adaptive signal filtering optimizes response time
Temperature & pressure compensation
Internal zero & span check (optional)
Comprehensive internal data logging with programmable averaging periods
Ability to log virtually any operating parameter
Two-year warranty
| Ranges: | Min: 0-50 ppb Full scale\nMax: 0-20000 ppb Full scale (selectable\nindependent NO NO2 NOx ranges and auto\nranging supported) |
| Measurement Units: | ppb ppm µg/m3 mg/m3 (selectable) |
| Zero Noise: | < 0.2 ppb (RMS) |
| Span Noise: | < 0.5% of reading (RMS) above 50 ppb |
| Lower Detectable Limit: | 0.4 ppb |
| Zero Drift: | < 0.5 ppb/24 hours |
| Span Drift: | < 0.5% of full scale/24 hours |
| Lag Time: | 20 seconds |
| Rise and Fall Time: | < 60 seconds to 95% |
| Linearity: | 1% of full scale |
| Precision: | 0.5% of reading above 50 ppb |
| Sample Flow Rate: | 500 cm3/min ±10% |
| Power Requirements: | 100V-120V 220V-240V 50/60 Hz |
| Analog Output Ranges: | 10V 5V 1V 0.1V (selectable) |
| Recorder Offset: | ±10% |
| Included I/O: | 1 x Ethernet: 10/100Base-T\n2 x RS232 (300-115200 baud)\n2 x USB device ports\n8 x opto-isolated digital outputs\n6 x opto-isolated digital inp |
| Optional I/O: | 1 x USB com port\n1 x RS485\n8 x analog inputs (0-10V 12-bit)\n4 x digital alarm outputs\nMultidrop RS232\n3 x 4-20mA current outputs |
| Operating Temperature Range: | 5 - 40ºC (with EPA Equivalency) |
| Dimensions (HxWxD): | 7 x 17 x 23.5 (178 x 432 x 597 mm) |
| Weight: | Analyzer: 40 lbs (18 kg)\nExternal pump: 15 lbs (7 kg) |
| US EPA: | RFNA-1194-099 |
| MCERTS: | Sira MC 050068/05 |
| EN 14211 | TÜV Rheinland |