24/7 Technical Support

Pine offers a wide range of air sampling accessories such as filters and sample containers. Please contact your local office for details.

To find out more, please click on a product from the list. At Pine, we specialize in delivering total equipment solutions and providing technical advice on what to rent and how to use it; our rental fleet is second to none and our equipment is always tested and delivered ready to use.


Drager Short-term Tubes
Drager Short-term Tubes

For spot measurement more than 500 different gases can be detected. The measurement usually takes between 5 seconds and 15 minutes. Furthermore, the easy-to-use Dräger-Tubes have already been calibrated and form a complementary unit with the Dräger-Tube pumps.

The Dräger Short-term Tubes are used either manually with the Dräger-Tube pump accuro or automatically with the Dräger X-act 5000. The results can then be read directly at the end of the measurement process.

A large number of different gases and vapors can be measured by the Dräger Short-term Tubes. These tubes are used e.g. for the determination of concentration peaks, the measurement of exposures in the inhalation area, the determination of possible leakages as well as for the analysis of air in sewers, shafts, tanks or other confined spaces.air examinations at the workplace in the range of legal limit values.

 

show more

Drager Tube Accuro Hand Pump
Drager Tube Accuro Hand Pump

Mobile spot measurement
This manual pump is used for spot measurements such as the detection of concentration peaks, confined space entry, worst-case scenarios etc.

Sampling
During the sampling process the substances to be evaluated are firstly accumulated on a suitable carrier material, e.g. activated charcoal, silica gel and so on. The air to be evaluated is thereby drawn over the respective material - with a predefined flow rate and duration. Afterwards, the substances that have accumulated on the carrier material through adsorption or chemisorption are examined qualitatively and quantitatively in the laboratory using instrumental analysis such as gas chromatography.

Functional bellows pump
The Dräger-Tube pump accuro draws in 100 ml per stroke. When measuring, the pump body (bellows) is pressed together completely. The exhaust valve is closed during the opening phase of the bellows so that the gas sample flows through the connected Dräger-Tube into the pump. After the complete opening of the pump body into its original position the suction process is finished. The end of stroke is visible by a pressure-controlled end of stroke indication, located in the pump head.

One-handed operation
Frequently, measurements need to take place under extreme conditions, e.g. on ladders, in shafts or when wearing heavy breathing protection. The Dräger-Tube pump accuro can easily be operated with one hand and enables a reliable measurement also in difficult-to-access places.

show more

Drager-X-act 5000
Drager-X-act 5000

The automatic tube pump Dräger X-act® 5000 is the first all-in-one solution designed for measurements with Dräger Short-term Tubes and for Sampling Tubes and Systems. Ease of operation and a high degree of reliability compliment the measurement and sampling of gases, vapors and aerosols.

show more

Dwyer Series 2000 Magnehelic® Differential Pressure Gage
Dwyer Series 2000 Magnehelic® Differential Pressure Gage

Multiple Pressure Ranges Available

Select the Magnehelic® gage for high accuracy--guaranteed within 2% of full scale--and for the wide choice of models available to suit your needs precisely. Using Dwyer's simple, frictionless Magnehelic® gage movement, it quickly indicates low air or non-corrosive gas pressures--either positive, negative (vacuum) or differential. The design resists shock, vibration and over-pressures. No manometer fluid to evaporate, freeze or cause toxic or leveling problems.

The Magnehelic® gage is the industry standard to measure fan and blower pressures, filter resistance, air velocity, furnace draft, pressure drop across orifice plates, liquid levels with bubbler systems and pressures in fluid amplifier or fluidic systems. It also checks gas-air ratio controls and automatic valves, and monitors blood and respiratory pressures in medical care equipment.

Note: May be used with Hydrogen. Order a Buna-N diaphragm. Pressures must be less than 35 psi.

show more

Mesa Labs DC-LITE 1 - 40LPM
Mesa Labs DC-LITE 1 - 40LPM

The DryCal DC-Lite offers a primary flow standard that can be used for accurate calibration of all commercially available industrial hygiene and environmental air sampling pumps. Convenient features include AC/DC operation, a large alphanumeric LCD for flow rate, flow average with number of readings included in the average push-button read and auto-read of volumetric flow rate, automatic shut-off, a parallel printer port that interfaces with most PC-compatible printers - and no messy soap film. Three models of the DC-Lite Calibrator are available for rental: Model DCL 12K (10ml/min to 12LPM), Model DCL 20K (20ml/min to 20 LPM) and Model DCL 40K (1 to 40 LPM).

show more

Mesa Labs Defender Primary Flow Meter
Mesa Labs Defender Primary Flow Meter

Mesa Labs Defender 510 and Defender 520 are the next generation of the DryCal® DC-Lite and DryCal® DC-2 flow Calibrators.

Everything you trusted about Mesa Labs DryCal® technology in the DC-Lite and DC-2 digital flowmeters is available in the Defender 510, 520 & 530 calibrators that make it easier than ever to calibrate air sampling pumps. Measure volumetric flow, standarized flow, which correct for temperature and pressure, or calibrate devices that read in mass flow.

Mesa Labs Defenders are true primary flow meters designed to provide light weight ultra-compact size, incorporating the industry leading DryCal technology. Building on the patented DryCal near-frictionless piston technology, the Defender 500 series incorporates features to make it immune to flow source pulsation without the need for in-line dampers.

Like all Mesa Labs calibrators, the Defender calibrator is easy to use.  Turn it on. Connect it to a sampling pump. Start taking readings. It's as simple as that. Calibrations within a minute with no messy soap bubble solutions to wait on or clean up after.

The Defender 510, 520 and 530 can take hands-free continuous readings while quickly and accurately setting the flow rate on air sampling pumps or other instruments. The Defender calibrators connect to any PC and pre- and post-calibration data can be downloaded with the included Optimizer Collect Light software.

show more

SKC 1L Vac-U-Chamber
SKC 1L Vac-U-Chamber

The SKC Vac-U-Chamber is a rigid air sample box that allows sample bags to be filled directly by using negative presure provided by most personal air sample pumps. Since the air sample does not pass directly through the pump, both pump and sample contamination are eliminated. The Vac-U-chamber's rigid walls will not collapse under vacuum conditions. All surfaces in contact with the sample are constructed of stainless steel or teflon for intertness.

show more

TSI 4046 / 4146 Sampling Pump Primary Calibrator
TSI 4046 / 4146 Sampling Pump Primary Calibrator

Personal samplin relies upon the accuracy of the data being generated which is where the TSI 4146 Cablibrator comes in. With a range of 0.01 to 20 l/min, the 4146 provides increased levels of confidence in your sampling. Compact and battery operated, the unit continuously displays real-time volumetric flow rate so adjustments can easily be made.

The 4146 measures flow rates of 0-20 l/min, whereas the 4046 measures flow rates of 0-300 l/min.

show more